Recent developments of high-performance NEOMAX magnets

For further improvement in achieving extremely high magnetic properties of Nd- Fe- B sintered magnets, extensive investigation has been done to densify the magnet up to the theoretical value, to increase the volume fraction of the Nd ₂Fe₁₄B matrix phase, and to achieve a high degree of alignment. By controlling chemical composition and the amount of constituent phases,improving particle size distribution, and adopting the isostatic pressing method to get better alignment of fine particles, we have succeeded in obtaining a high-performance magnet having residual flux density (B_r) of 1.495 T (14.95 kG), maximum energy product [(BH)_max] of 431 kj/m³ (54.2 MGOe), and intrinsic coercivity (iH_c) of 845 kA/m (10.62 kOe).     

Initial Stages in the Metal-dusting Process on Alloy 800

The initial stages of the metal-dusting process on Alloy 800 at 620 °C were investigated by light optical microscopy, RAMAN spectroscopy, atomic-force microscopy, Auger electron spectroscopy, transmission-electron microscopy and electron back-scatter diffraction. As it turned out the incubation period for metal-dusting is characterized by simultaneous formation of a heterogeneously growing oxide scale and deposition of carbon. The material surface shows different tarnish colors depending on the substrate-grain orientation with different susceptibility to the beginning of metal-dusting attack. “Low-index” grains were not attacked within the times investigated while the other grain orientations showed pitting. Carbon is evidently incorporated into the oxide scale from the very beginning of exposure with different intensities depending on the underlying substrate-grain orientation leading to differences in the tarnish colors. As a consequence carbides are formed even underneath “dense” oxide layers. Evidently metal-dusting attack starts at positions of the oxide scale where “higher carbon concentrations” are present.     

基于小波分析的捷联式惯导系统的初始对准方法研究

对于光纤陀螺捷联式惯导系统，提出了一种新的初始对准方法，采用小波分析方法撮初始对准的有用信号；用二位置法确定初始方向余统矩阵，同时对光纤陀螺的常值漂移和加速度计零偏置进行标定。仿真结果表明了这种方法的有效性。     

用介孔材料制备定向碳纳米管的研究进展

综述了近年来采用介孔材料制备定向碳纳米管的研究进展,包括介孔材料的合成及介孔材料在制备定向碳纳米管方面的应用。重点介绍了采用合成介孔材料的模板剂石墨化及介孔材料作为载体制备定向碳纳米管的方法,探讨了模板剂种类、催化剂的制备方法及反应温度和时间对定向碳纳米管生长的影响和定向碳纳米管生长的介孔限制机理,并提出了这一领域的研究方向。     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

垂直定向液晶光阀及光电特性的研究

系统地讨论了排列相畸变模式液晶光阀结构，原理和制作，结合实际测试对其等效电路和电学匹配进行了分析，详细讨论了它的光电特性及相互关系，实测的液晶垂直排列方式工作的液晶光阀性能指标为，分辨率大于５０ｌｐ／ｍｍ，白光输入灵敏度为６．７７μＷ／ｃｍ＾２，响应时间为２００ｍｓ／３００ｍｓ，白光输出对比度为２００：１。     

The effect of fibre alignment on composite strength: II. The strength of angle-ply laminates

Experiments have been carried out on relatively wide angle-ply laminate samples with very short gauge lengths. These proved to be very much stronger than samples tested in earlier work, and which form the basis for our present design with these materials. It is highly likely that the early results for strength were more indicative of edge effects than true laminate strength. This is confirmed by data from tests on pressurized tubes. A review of the literature on this shows that such tests produced results which can be an order of magnitude higher than the early laminate tests. Thus our design calculations could well be severely underestimating the potential strength of angle-ply laminates. This may be having serious consequences for the aerospace industry, through the use of design criteria for strength which may be too conservative. Single-fibre experiments may pave the way for more realistic estimates of angle-ply laminate strengths. These indicate that a simple one-third power rule can be used to estimate the potential strength. However, this is purely ad hoc at present, and needs to be put on a firmer footing through both theoretical and experimental studies. Furthermore, if this approach is adopted, edge effects will still have to be allowed for, and estimated on the basis of the aspect ratio of the part.     

The IS Organization of the Future: Four Scenarios for 2020

Four scenarios for the IS organization of 2020 are described, based on differing assumptions about two drivers: the advances in the reliability of international telecommunications and the value placed on computerization in businesses and society.     

回转窑大齿圈的安装与找正

根据回转窑大齿圈结构特点，阐述了回转窑大修中两个半齿圈组装、校正及与简体的安装、找正方法以及重要工艺过程中的注意事项，在山西铝厂2^#熟料窑大修中取得了良好效果。